Does a high-density or AI data hall change how the electrical thermography survey is done?

The method stays the same: image the power path live, under load, and compare like with like. What changes is where the load sits and how fast it moves. Rack PDUs, tap-offs and overhead busbar carry more of the current, liquid-cooling supplies join the scope, and the load at the moment of each image matters even more.

A high-density hall is still a data hall. The switchboards, UPS, busbar and PDUs are surveyed live with nothing switched off, as on any other site (see data centre electrical thermography). Four things deserve more attention.

1. More current at the end of the power path

When each rack draws more power, the circuits that feed it carry more current. That puts more weight on the parts of the path that a switch-room-only survey never reaches: the busbar run over the racks, each tap-off unit, the rack PDU inlet and its outlets. A survey of a high-density hall should follow the power all the way to the rack (see the whole power path, intake to rack), with overhead busbar and tap-offs imaged from the floor or a platform under the site’s access rules (see overhead busbar in a live data hall).

2. Load that moves

An enterprise hall tends to draw a steady load. A hall running large compute jobs can swing as work starts and stops. A connection imaged while its cluster is idle tells you far less than the same connection imaged mid-job. So:

  • Ask the operations team when the hall usually runs at sustained load, and survey then.
  • Record the current on each circuit at the moment it is imaged, from the PDU display, BMS or branch monitoring.
  • Where a run was imaged at light load, the report says so plainly and lists it for a repeat visit.

This is the same principle as any live survey (see what load a meaningful survey needs), just with less margin for getting the timing wrong.

3. Liquid cooling adds electrical scope

Halls cooled by liquid bring extra electrical equipment into the room: supplies to coolant distribution units, their pump panels, and fan supplies to rear-door heat exchangers. These are electrical connections like any other and belong in the survey. The coolant pipework and manifolds are not electrical findings; a cold pipe or a warm return line is the cooling system doing its job and is not reported as a fault. The plant-room side is covered in chiller, CRAH and pump panels.

4. A hotter rear of rack

Dense racks push more heat into the hot aisle, so everything at the back of the rack reads warm. An absolute temperature means little there. Each PDU and outlet is compared with the same model on neighbouring racks, the other feed on the same rack and matching outlets on the same strip, allowing for any difference in load (see rack PDUs in a live data hall). Time in a contained hot aisle is planned with the site, including breaks.

New halls fill quickly

A high-density hall can go from load bank to busy in months. Commissioning thermography under test load sets the baseline. A second survey once the racks are carrying real work, rather than waiting for the annual date, catches anything that only shows under the hall’s own load (see busbar thermography at commissioning and annual PPM thermography).

What the report gives you

Each finding is located by hall, busbar run, tap-off, rack and feed, with a thermal and visual image pair, the measured temperature, where it was taken, the difference in °C from its matching reference and the current at the time. Anything not imaged is listed with the reason. We deliver reports the same day. Ti inspects and reports; the operator’s electrical team or contractor investigates any finding.

Why the load matters

On a London data centre build, commissioning thermography by our team found 16 busbar sections reading above 80 °C under test load, the highest 103.5 °C at a tap-off unit. Those connections showed their condition because they were carrying current when they were imaged.

Frequently asked questions

Can the survey run while compute jobs are running?

Yes, and that is the best time. Nothing is unplugged or switched; site staff open rack doors and panels one at a time.

Does cooling need to be changed for the survey?

No. The hall is surveyed as it normally runs. The report notes the cooling arrangement so next year’s survey compares like with like.

How often should a high-density hall be surveyed?

Most operators survey annually, with an extra visit when a hall’s load rises noticeably or a new block of racks is energised (see 7 electrical risks thermography finds).

Related reading

Ti Thermal Imaging’s surveys are carried out by ITC Level 3 thermographers, and Ti is a Level 3 certified company. Our work has featured on BBC News and ITV.

Talk to us: +44 20 3885 7464 · sales@thermalimaging.co.uk · contact page

About the author: Rachael Browning, General Manager, Ti Thermal Imaging.