What should an electrical thermography survey cover at a sawmill or joinery works?

Short answer: a sawmill or joinery works survey should cover the incoming supply and main switchboard, the MCCs and starters for saws, planers and moulders, the dust extraction fan and filter panels, kiln and dryer controls, and the conveyors and handling plant. Dust-hazard zones are agreed with the site first. Image during a normal production shift, with machines cutting and extraction running.

Why wood processing sites need a planned survey

A sawmill or joinery works runs on big motors that start and stop all day: band and circular saws, chippers, planers, moulders, CNC routers and edge banders, all tied to a dust extraction system that has to run whenever they do. When the extraction fan trips, the machines it serves usually have to stop with it.

Thermography checks the connections feeding that equipment under real load, with nothing switched off. Anything that stands out goes in the report with its location and reading, so the site can plan any work into the next maintenance stop rather than lose a shift to a breakdown.

What to include

  • Incoming supply, main LV switchboard and sub-boards for the mill, workshops, yard and offices
  • MCCs and starters for headrigs, band and circular saws, chippers and debarkers
  • Machine panels and drives for planers, moulders, CNC routers, edge banders and sanders
  • Dust extraction: fan motor starters and drives, filter and rotary valve panels, and the boards that feed them
  • Kilns and dryers: fan, heating and control panels, including any boiler or biomass plant supplies
  • Handling plant: log decks, conveyors, stackers, wrapping lines and forklift charging
  • Support plant: compressors and spray booth supplies

Dust-hazard zones

Wood dust is combustible, and parts of a sawmill or joinery works will be classified under the site’s own DSEAR assessment, most often around filters, silos and the extraction ductwork. Most MCCs and switchrooms sit outside those zones. Anything inside a zone is only opened and imaged if the site’s assessment and permit allow it; otherwise it is listed on the report as not imaged, so nobody assumes it was checked.

Timing: a normal cutting shift

Saws, planers and moulders draw their heaviest current while they are cutting, and the extraction fans run hardest when most machines are working at once. A survey on a quiet afternoon or during a changeover will show far less. We agree the route with the production manager so each panel is imaged while its machines are running, and the load is recorded with every image so next year’s survey compares like with like.

Kilns are planned separately: their fans and heating run on a long cycle, so we image the kiln panels part-way through a drying run, not at the start or end.

Heat traps a thermographer has to rule out

  • Dust on covers and components: a layer of sawdust changes what the camera sees, so readings are taken on the connection itself with the cover open where it is safe to do so.
  • Warm by design: motors, gearboxes, kiln casings and heating coils run warm in normal service. Readings are taken at the electrical connection, not the machine body.
  • Bare metal and reflections: shiny busbars, enclosure walls and saw guards can reflect heat from nearby sources, so suspect readings are checked from a second angle.
  • Sun on yard kiosks: outdoor panels for log decks and yard lighting can be heated by direct sun, so they are compared with matching panels before anything is reported.

What the report gives you

Each finding comes with its location by panel and circuit, a thermal image with a matching photo, the measured temperature, the load at the time and the difference in °C from a matching phase or identical unit. Ti inspects and reports; your maintenance team or electrical contractor carries out any work. Reports are on our online portal, usually the same or next working day, in a format insurers and auditors recognise.

Who should do it

Look for a thermographer certified to at least Level 2, with Level 3 oversight, who works within your permit-to-work. Ti Thermal Imaging’s surveys are carried out by ITC Level 3 thermographers, and Ti is a Level 3 certified company. Your authorised electrician opens and closes panel covers; our thermographer does not touch live equipment.

Frequently asked questions

Does production need to stop?

No. Thermography needs the equipment running. Covers are opened one at a time by your authorised electrician while the site keeps working.

How often should a sawmill or joinery works be surveyed?

Once a year is a common minimum, and often what insurers ask for. Sites running double shifts, or with older MCCs, often survey every six months.

Can the dust extraction system be surveyed while it runs?

Yes, and it should be. The fan starters, drives and feeder boards are imaged at working load. Filter and rotary valve panels inside a classified zone are only opened if the site’s DSEAR assessment and permit allow it.

Related reading

Talk to us: +44 20 3885 7464 · sales@thermalimaging.co.uk · send us your site details

About the author: Rachael Browning is General Manager of Ti Thermal Imaging, which carries out electrical thermography for data centres, FM portfolios and industrial sites across the UK and UAE. Ti’s work has featured on BBC News and ITV.